Rigging and Flying Instructions for BASSBOSS Loudspeakers

Rigging and Flying Instructions for BASSBOSS Loudspeakers

Caution:

This article describes the best practices for flying BASSBOSS products.  Note that not all models include flypoints - models such as the DJ18S without flypoints are not intended to be flown.  Be sure to follow all relevant safety guidelines in your area and hire a qualified rigger if you are unsure how to safely fly loudspeakers.  Accidents due to improper flying can result in death, and BASSBOSS is not responsible for injury or fatalities due to improper flying!

Models with Built-in Flypoints:

Model
Suspension System
AT212
4x internally braced M10 threaded mounting points
AT312
4x internally braced M10 threaded mounting points
CCM12
12x internally braced M10 threaded mounting points
DV12
8x internally braced M10 threaded mounting points
MFLA
Integrated line array flyware, adjustable in one degree increments from 0 to 10 degrees
Krakatoa
16x internally braced M10 threaded mounting points 
Kraken
16x internally braced M10 threaded mounting points 
SSP118
8x internally braced M10 threaded mounting points
SSP215
16x internally braced M10 threaded mounting points 
SSP218
16x internally braced M10 threaded mounting points 
VS21
16x internally braced M10 threaded mounting points 
ZV28
16x internally braced M10 threaded mounting points 

Models without built-in flypoints (not intended to be flown):

Model
Note
DiaMon
Use DiaMon ceiling mount for hanging/mounting 
DJ18S

Makara

Sublim8
Includes eyebolts for mounting a lighting fixture but not for flying the unit - do NOT attempt to fly the top section of the Sublim8 via the eyebolts!
SV9
Use DiaMon ceiling mount for hanging/mounting                                                                                                                         |

What to do when flying your BASSBOSS Loudspeaker?

  1. BASSBOSS Loudspeakers can be flown with side-pull anchors or shoulder eyebolts, depending on how you wish to fly them:
  2. If using side-pull anchors:
    1. We recommend replacing the included M10x25mm flat head socket cap screws with M10 x 40-50mm button head socket cap screws to attach the side-pull anchors
    2. The benefits of using side-pull anchors is that you can get a cabinet closer to the ceiling, as shoulder eyebolts will stick out above the cabinet. 
    3.  We recommend using side-pull anchors when flying subs near a ceiling and near a rear boundary
    4. Side-pull anchors are typically more popular for flying subs
  3. If using M10 shoulder eyebolts
    1. Replace the included M10x25mm flat head socket cap screws with M10 shoulder eyebolts at the locations in which you want to fly the cabinet
    2. We recommend using a shoulder eyebolt if flying the speaker from above or at a slight angle.
    3. Shoulder eyebolts are typically more popular for flying tops
  4. Use 4 of the included M10 threaded mounting points when flying your BASSBOSS subs and large format tops like the Krakatoa, and at least 2 when flying BASSBOSS tops

What NOT to do when flying your BASSBOSS Loudspeaker:

  1. Do NOT fly your cabinet from the handles
  2. Do NOT drill or screw into cabinets to attach lifting points
  3. Do NOT fly cabinets by any other mechanism than the factory installed, internally secured M10 fly points

Maintaining your flown product:

  1. Check the security/tightness of all load-bearing fasteners regularly.
  2. Check all hardware for visible signs of wear and tear, and replace when necessary. 

See Also:

  1. Where can I purchase replacement hardware for cabinet flypoints?
  2. What should I use to mount my SV9, DiaMon, or CCM?
  3. Which Poles and Tripods do you recommend for BASSBOSS Loudspeakers?